RSS
» کار عملی 16 - درایور ترانزیستوری موتور ( پل اچ) ( یکشنبه بیست و هشتم مهر ۱۳۹۲ )
» ویژه تابستان 95 ( جمعه هفتم خرداد ۱۳۹۵ )
» کلاس های تابستان 1395 در حال شروع شدن ( دوشنبه سوم خرداد ۱۳۹۵ )
» خبرهای خوشی در راه است... ( سه شنبه بیست و پنجم فروردین ۱۳۹۴ )
» کتاب آموزشی CodeVision AVR ( یکشنبه چهارم آبان ۱۳۹۳ )
» نرم افزار CodeVision AVR ( یکشنبه چهارم آبان ۱۳۹۳ )
» نرم افزار طراحی رگولاتور ولتاژ و جریان ( یکشنبه چهارم آبان ۱۳۹۳ )
» آیا عطسه‌ نشانه صبر در انجام کارهاست؟ ( سه شنبه بیست و یکم مرداد ۱۳۹۳ )
» یادش بخیر - شبهای قدر دوران کودکی ( جمعه بیست و هفتم تیر ۱۳۹۳ )
» اطلاعیه کار آموزی ویژه تمامی رشته ها و گرایش های مهندسی ( سه شنبه بیست و چهارم تیر ۱۳۹۳ )
» پانته آ ( یکشنبه بیست و دوم تیر ۱۳۹۳ )
» العجل مولا ( جمعه بیستم تیر ۱۳۹۳ )


Click to enlarge


This project is 6" seven-segment.All segments consist of fourteen 5mm super bright LEDs except dot segment it use only 4 LEDs.I design this project use for multipurpose such as big 7-segemnt display ,big digital clock,digital timer etc.The project designed as a module for one digit .You can cascade up to 8 module or 8 digits. For each digit there are two options on PCB which you can use or ignore these options for each digit PCB.
- 3 switches on PCB.
- 1 Opto-isolate input.


PIC16F876A to be used to control all of task on this project.You can replace with any 28 pin PIC microcontroller.PortB set as output to drive all segments.PortC set as output to drive each digit vai ULN2803 which is octal hight voltage ,high current darington transistor array.



Jumper 1(J1) on PCB used to determine digit itself module(digit1 - digit8). 

The solder pad at the bottom of PCB use forcascade the digit. It include with all segments of a,b,c,d,e,f,g,h,dot(p) and digit1- digit 8.Tocascade the digit you just solder the PCB pad then select the J1 to determine the digit itself. If the digit place away for each digit you can use coper wire or flat cable instead as show in the belowpicture.


Click to enlarge



The example firmware included in this project is 4 digits counter writen for CCS C compiler.You can modify the source code if you want more than 4 digits. To use with this example firmware you must assembly 1 complete PCBs (all components installed) and the rest of 3 PCBs you need to solder all LEDs only.Then determine the complete PCB to be digit 1 by jumper 1 and the rest of 3 PCBs determine to be digit 2, 3 and 4 respectively. 


click to enlarge

click to enlarge


PCB and schematic
include bottom,over lay,composite 
in pdf file format



برچسب‌ها: Big 7, segment
دسته بندی : جمع آوری پروژه های میکروکنترلری

موضوعات
آرشیو مطالب
نویسندگان
درباره ما

    بسیجی گمنام خمینی ٍ "" و لا یحمل هذا العلم الا اهل البصر و صبر و العلم به مواضع حق ""
    و این پرچم مبارزه را جز افراد با بصیرت و صبور و آگاه به جایگاه حق به دوش نمی کشند .

    این وبلاگ متعلق به گروهی از سربازان حقیقی حضرت بقیه الله الاعظم می باشد که در عرصه جهاد علمی و فرهنگی فعالیت می کند .

    ایمیل : malekipcb@gmail.com